Water Heater Replacement or Repair? The Best Water Heater Service Has Solutions for Homes in Beaver Dam!

 It’s a moment no one enjoys: In the midst of a hot, steamy shower, the water abrubtly turns icy.

 

The shower likely ends rapidly. What happened?

 

The discomfort in this scenario is no mystery. Source of the problem? Not so much.

 

The problem goes back to the water heater. This Beaver Dam household appliance, like many, is often ignored until something stops working.

 

When the hot water goes cold, one question looms large over this quiet appliance: Repair or replace?

 

The answer lies in another question: Why? As in, why did the water heater stop working?

 

Regardless, you need your hot water back – and soon. The prudent move is to contact Brandt Plumbing, the top water heater repair and replacement company (and plumbing services provider) in Beaver Dam. Their residential plumbing pros will quickly restore comfort to your showers! 

Why is my water heater not functioning? Repair or replace?

Water heaters usually fail from hot water tank corrosion. If a tank rusts through, water heater replacement is necessary – case closed. If you discover a trickle of liquid on the floor leading to the water heater, prepare to purchase a new one.

 

If there’s no discoverable leak, a water heater repair could be in order. Many interior water heater parts can go bad: thermostats, heating elements, gas control valves, dip tubes, and T&P valves. Fortunately, all can usually be replaced.

 

Most Beaver Dam residential water heaters operate eight to 12 years for gas units, 10 to 15 for electric. If your unit is still comparatively young, and the problem is connected to a replaceable component, repair is often the financially-sound choice.

 

If the tank is leaking, though, or the unit is near the end of its shelf life … well, replacement is likely needed. It’s more cost effective, too (count on $1,500 to $2,500), than repairing. 

How are water heaters replaced?

Water heater professionals in Beaver Dam, like those at Brandt Plumbing, can safely take out a failing water heater and install its replacement.

 

Most homes use 40-50 gallon models. Brandt Plumbing can install units up to 100 gallons. If space is limited, short/low-boy tanks can usually suffice.

 

The water heater replacement process is pretty straightforward. After turning off water and gas, the old tank is drained. It’s taken out after plumbing and venting are disconnected.

 

The new water heater is put in place. Connections are restored. The tank is filled, tested, and its heater turned on.

 

Minor replumbing is occasionally needed. If the unit being replaced is old, plumbing codes might necessitate an upgrade. Venting or gas line sizing could need improvement. The new heater might be a different height. Or, old shutoff valves might leak or be inoperative. 

How can I extend my water heater’s life?

Water quality and maintenance play big roles in a water heater’s longevity. A few small measures can add years to a heater’s life.

 

Sediment buildup in the tank will quicken its failure. Flushing the tank annually helps alleviate this risk.

 

If water is very hard, which in Beaver Dam it might be, a water softener makes a noticeable difference. High water pressure takes its toll, too – keep pressure in the system below 75 PSI for best results.

 

Replace the anode rod every few years. Set the temperature between 120 and 130 degrees.

 

These small efforts can substantially forestall the cost and trouble of water heater replacement or repair. Why not make them? 

What about tankless water heater installation?

Tankless water heaters are increasingly popular. Unlike regular water heaters – where water enters a tank, and is heated and stored until used – a tankless system is basically an on-demand heat exchanger.

 

When a hot water tap is opened somewhere within a home, the flow sensor in the tankless system activates the burner (for gas) or heating element (for electric). Water is rapidly warmed as it passes through, before going to the shower, faucet or appliance where needed.

 

Because no water is stored, no heat loss happens. Energy savings can be substantial. The supply of hot water is essentially limitless, too, as long as flow rate stays within the unit’s capacity. No more fear of running out!

 

Tankless water heater systems are nearly always wall mounted. Sizes range from 20 to 30 inches in height, and 12 to 20 inches wide. They’re deep, too – eight to 12 inches.

 

Some replumbing is typical. Water lines must be rerouted. Sometimes pipes, too. A larger gas line is usually involved, due to high fuel demand while the unit is operating.

 

A new outside vent will probably be required. If the unit is in a closet or small space, likely an air intake, too. Finally, a 120-volt outlet is necessary.

 

Brandt Plumbing has installed many tankless water heaters. Cost is usually $3,000 to $6,000. The variance depends on the model used, or if recirculation pumps or complex venting are needed. Don’t hesitate to ask questions – tankless systems are popular for a reason!

 

Hot water isn’t a luxury. It’s a requirement for comfortable modern living. If yours goes out, don’t put up with the discomfort for long. If you live near Beaver Dam, contact Brandt Plumbing for water heater repair or replacement that will have you singing in the shower again!