Water Heater Replacement or Repair? The Best Water Heater Service Has Solutions for Homes in Lannon!

 It’s a moment no one enjoys: In the throes of a hot, steamy shower, the water abrubtly turns cold.

 

The shower probably ends quickly. What happened?

 

The discomfort in this scenario is understandable. Source of the problem? Not so obvious.

 

The problem goes back to the water heater. This Lannon household appliance, like many, is usually neglected until something stops working.

 

When the hot water goes cold, one uncertainty stands tall above this quiet appliance: Repair or replace?

 

The answer lies in another question: Why? As in, why did the water heater stop functioning?

 

Regardless, you want your hot water back – and soon. The advisable move is to contact Brandt Plumbing, the top water heater repair and replacement company (and plumbing services provider) in Lannon. Their residential plumbing experts will quickly bring back comfort to your showers! 

Why is my water heater not functioning? Repair or replace?

Water heaters regularly fail from hot water tank corrosion. If a tank rusts through, water heater replacement is necessary – case closed. If you discover a trickle of liquid on the floor coming from the water heater, get ready to buy a new one.

 

If there’s no discoverable leak, a water heater repair could be on tap. Many interior water heater parts can fail: thermostats, heating elements, gas control valves, dip tubes, and T&P valves. Fortunately, all can usually be replaced.

 

Most Lannon residential water heaters function eight to 12 years for gas units, 10 to 15 for electric. If your unit is still somewhat young, and the problem is linked to a replaceable component, repair is often the financially-sound choice.

 

If the tank is leaking, though, or the unit is near the end of its lifespan … well, replacement is likely in the cards. It’s more cost effective, too (count on $1,500 to $2,500), than repairing. 

How are water heaters replaced?

Water heater professionals in Lannon, like those at Brandt Plumbing, can safely remove a failing water heater and put in its replacement.

 

Most homes use 40-50 gallon models. Brandt Plumbing can install units up to 100 gallons. If space is limited, short/low-boy tanks can typically suffice.

 

The water heater replacement process is largely straightforward. After turning off water and gas, the old tank is drained. It’s removed after plumbing and venting are disconnected.

 

The new water heater is put in place. Connections are restored. The tank is filled, tested, and its heater turned on.

 

Minor replumbing is occasionally needed. If the unit being replaced is old, plumbing codes might mandate an upgrade. Venting or gas line sizing could need improvement. The new heater might be a different height. Or, old shutoff valves might leak or be inoperative. 

How can I extend my water heater’s life?

Water quality and maintenance play big roles in a water heater’s lifespan. A few small measures can add years to a heater’s operation.

 

Sediment buildup in the tank will quicken its failure. Flushing the tank annually helps alleviate this risk.

 

If water is very hard, which in Lannon it might be, a water softener makes a big difference. High water pressure takes its toll, too – keep pressure in the system below 75 PSI for best results.

 

Replace the anode rod every few years. Set the temperature between 120 and 130 degrees.

 

These small efforts can substantially forestall the cost and trouble of water heater replacement or repair. Why not make them? 

What about tankless water heater installation?

Tankless water heaters are increasingly sought by homeowners. Unlike standard water heaters – where water enters a tank, and is heated and stored until used – a tankless system is basically an on-demand heat exchanger.

 

When a hot water tap is opened somewhere within a home, the flow sensor in the tankless system activates the burner (for gas) or heating element (for electric). Water is rapidly warmed as it passes through, before heading to the shower, faucet or appliance where needed.

 

Because no water is stored, no heat loss occurs. Energy savings can be substantial. The supply of hot water is essentially limitless, too, as long as flow rate stays within the unit’s capacity. No more fear of running out!

 

Tankless water heater systems are nearly always wall mounted. Sizes range from 20 to 30 inches in height, and 12 to 20 inches wide. They’re deep, too – eight to 12 inches.

 

Some replumbing is typical. Water lines must be rerouted. Sometimes pipes, too. A larger gas line is usually involved, due to high fuel demand while the unit is operating.

 

A new outside vent will probably be required. If the unit is in a closet or small space, likely an air intake, too. Finally, a 120-volt outlet is necessary.

 

Brandt Plumbing has installed many tankless water heaters. Cost is usually $3,000 to $6,000. The variance depends on the model used, or if recirculation pumps or complex venting are needed. Don’t be afraid to ask questions – tankless systems are popular for a reason!

 

Hot water isn’t a luxury. It’s a necessity for comfortable modern living. If yours goes out, don’t put up with the discomfort for long. If you live near Lannon, contact Brandt Plumbing for water heater repair or replacement that will have you singing in the shower again!